Sometimes what’s wrong with your air conditioning and heating system really doesn’t require the service of an expert repair person. Here are some common troubleshooting tips to go over before you call for a repair. A/C Not Cooling or Blowing? Check circuit breakers at fuse box. The outdoor condenser unit and indoor air handler unit have their own breaker. Even if breakers appear to be in the correct position, they are often tripped. Flip circuit breaker off and back on. Indoor A/C Unit Leaking Water? If the unit is leaking water one of three possible things has occurred Drain line is plugged. Check to see if your A/C drain line outside your home is draining properly. If it is not you can clear it by attaching a wet vacuum to the outside. Evaporator coil is dirty. Dirt, mold, and algae are growing on your coil causing it to drip> Coil is frozen with ice. Your A/C is probably low on freon. You will need to turn off the A/C and call for service. A/C Fan Runs Continuously?

Make sure your thermostat is set to the “Auto” position. A/C Runs,Won’t Cool Below 78 degrees Your A/C is possibly low on freon Your ductwork in the attic is leaking Your A/C is old and inefficient and can not keep up with the heat load Your air conditioner is under sized for the heat load demand Are Some Rooms Warmer than Others? In the warmer room, make sure the vent is open or open it further. If this does not resolve the problem, the situation is the result of one of the following three conditions. The ductwork was not sized properly The system needs to be balanced by adjusting the air flow dampers in the grills The ductwork has come apart and is leaking cool air into the attic. Thermostat Not Registering Correct Temperature? A temperature reading of within three (3) degrees up or down is considered normal. New digital thermostats are more accurate. Musty or Mildew Odor? Your ductwork got wet and is giving off a musty odor or it’s possibly growing mold.

No filters were used and the ductwork is dirty and growing mold. No filters or wrong filters were used and evaporator coil is plugged up with algae, fungus, mold and bacteria. Drain pan is full of algae, fungus, mold and bacteria. Call for service and schedule an extensive 21-point Breathe Green Tune-Up When Do A/C Filters Need Cleaning? A/C filters should be kept clean or replaced monthly.You should be using filters with a minimum MERV rating of 8 or higher. Please visit our section on Indoor Air Quality (IAQ). As dirt, debris, pollen and spores accumulates on your coil over time it will grow fungus, mold and bacteria. This build-up will restrict your air flow and cause you to have less cooling throughout your house and, at the same time, increase your electric bill. The bacteria and mold spores will circulate through your entire home and possibly affect your allergies and your health.The only way to fix this problem is to have the coil professionally cleaned.

Why Should I Choose a Programmable Thermostat? Most programmable thermostats are capable of four different time and temperature settings. A programmable thermostat will reduce your power bill by fluctuating temperature settings while you are at work, away or asleep.We highly recommend this product. Is a yearly Tune-Up necessary? All A/C units should be maintained at least once per year.portable ac unit smells bad Burning Smell on Heat Mode?styrofoam inside ac unit Check the circuit breakers at fuse box. jeep wrangler ac drainPlease note that when using your heat for the first time in cool weather, you may smell a slight burning odor. Dust has accumulated over the months and is burning off the heating coils. This is normal and should last no more than 30 minutes.

No Heat Coming Out of the System? Make sure the heating temperature is set above the room temperature. Check to make sure the thermostat is set to “Heat” and “Auto” position. Flip your circuit breaker off and back on. Some units can take 60 to 90 seconds before the heat cycle turns on. If you’ve allowed ample time and still no heat, turn your thermostat to the “OFF” position and call for service. Heat From System is Not Warm Enough? Make sure the temperature is set above the room temperature. As air circulates through the system, repeatedly, it will get warmer. If you have had your heat on for over 3 hours and it’s still not getting warm you need to call for service. Make sure the thermostat is set to the “Auto” position. If the actual temperature is above the temperature set, call for service. If the actual temperature is below the temperature set, the heat will continue to run until it reaches the temperature for which it is set. If you find it hasn’t shut off after reaching the requested temperature, call for service.

Quality ProsGuaranteeContact UsWhy is My Outdoor Outlet Not Working?If you have been trying to put up lights to decorate your garden for a party or to enhance the security and found that the outdoor outlet does not work, you need to take steps to rectify this. Outdoor outlets that are exposed to the weather are more likely to fail than indoor outlets. However, with a little bit of patience and skill you can fix it on your own. Rain and WaterOften outdoor outlets are damaged because of their exposure to rain and water. Even when the outdoor outlets have some amount of protection from the weather, they can be affected by the damp and humidity in or emanating from the garden. When encountering an outdoor outlet that does not work, do not assume the worst and immediately call an electrical contractor or pull out all the wires. You can try to fix it yourself and certainly determine how to prevent this from happening again. Instead and furthermore,you should look for the simple solutions first and call the electrical contractor only if you are unable to locate the fault or rectify it on your own.

The first thing you need to do is check all the outlets in your home and identify those that do not work. You can use either a voltage tester or simply plug in a lamp to see if the various outlets work. If some outlets are not working, unplug lamps and appliances from them to eliminate the possibility that it is the appliance that is shorted and not the outlet. You should make a note of all the outlets that do not work. Check for tripped circuit breakers: The next step is to check for tripped circuit breakers and switch them on again. The circuit breakers will be in the main electrical panel that can be near the entrance, laundry room, basement, or garage. Since the tripped circuit breakers might not always be apparent, you should firmly switch all the breakers to the off position before switching them on. If a circuit breaker trips back to the off position, it could be because of a potentially hazardous ground fault or short circuit. Let this circuit switch remain in the off position until you have located and fixed the problem.

Intro to GFCIGround Fault Circuit Interrupters or GFCIs are outlets with test and reset buttons. The GFCIs are installed in areas of the home where the potential hazards for electrical shock are exceedingly great. They detect any leaks in the current and immediately shut off power. The GFCI detects any flow of current of even as little as 4 or 5 milliamps from the hot slot to the neutral slot and shuts down the power supply in one thirtieth of a second. Since electricians want to save money, they often connect standard outlets to a GFCI outlet. This means that even standard outlets will no longer work after a GFCI shuts down power. All GFCI protected outlets are expected to be labeled but the labels often fall off, especially outdoors. Get Your Outlet RepairedWhere do I Reset It? GFCIs are typically placed in bathrooms, laundry rooms, kitchens, garages, basements, and outdoors. When you find that some of the outlets do not work you should locate and reset all the GFCIs in your home and then test the outlets for power.

For this you need to press the GFCI test button. This should make the reset button pop out. If it does not, it can mean that there is no power to the GFCI outlet itself or that the GFCI is malfunctioning. If the reset button trips after popping out then it means that there is a dangerous power leak that needs to be fixed before you can switch it on. To fix the power leak you will need to check all the wiring in your home. Unless you are very comfortable with working with electrical circuits you should consider taking the help of an electrical contractor to locate and rectify the current leak. Preventing It in the FutureA tripped GFCI is an inconvenience and not a danger. In fact the GFCI shuts down to prevent alarming or significant damage to your home or you such as electrical shocks and even the chance of a fire erupting or starting. In order to prevent frequent shutting down of the GFCI you need to ensure that all the electrical appliances you use are working properly. The GFCI will shut down when you connect faulty electrical appliances to an outlet.

Another reason for the GFCI to shut down is that when using the GFCI outlets people might end up inadvertently pressing the test button. Children too might press the test button. To prevent such errors, you should ensure that children are not allowed to play with the GFCI outlet and take care when you plug in appliances to a GFCI outlet. In the long run, to ensure that you do not suffer from frequent GFCI shut downs, you need to get all your electrical appliances tested for faults and repaired as soon as possible. You can also consider taking the help of an electrician to check all the wiring in your home. The GFCI is a safety device that helps prevent hazardous electrical shocks and fires. This device works by shutting off electrical power to all the outlets connected to it. You can locate the fault, fix it, and reset the GFCI by pressing the test button.Popular Expert AnswersWhat’s wrong with my outdoor outlets that aren’t working?Can dirt cause an outdoor outlet to stop working?